Overview

Why choose ThermoCube 300A?

See the ThermoCube Model Comparison Table

Compact size: just 12” (30 cm) on a side
Precise temperature control (+0.05 °C) even near ambient
For use with CDA, N2, O2, argon or other inert gases
Very energy efficient (typically <200 W AC)
Whisper-quiet (as low as 49 dBA)
Worldwide power compatibility, universal input standard
Easy-to-use controller for fixed temperature control  or temperature cycling
Air-cooled.  Does not require house or facility chilled water.  Can operate in any standard room, laboratory or office.

Benefits of The ThermoCube 300A Air-cooled Pressurized Gas Temperature Controller

Reliable Freon-Free Thermoelectric Technology
The ThermoCube uses thermoelectric technology, widely used throughout the world for 50 years in various applications from spacecrafts to home appliances.  With lifetimes exceeding 200,000 hours, the thermoelectric modules at the core of this chiller make for ultra-high intrinsic reliability.

Optimized for Modest Heat Loads
ThermoCube 300A is available in 300 Watt capacity, for up to 300 slpm gas flows.

Whisper Quiet
With only one moving part, the cooling fan, ThermoCube 300A is quiet.  Available with four fan options and sound-dampening insulation, the quietest model runs at 49 dBA.

Precise Temperature Control
Because electrons transfer the heat, ThermoCube responds instantaneously to changes in load.  The digital PID temperature controller holds to < + 0.05 °C, even near ambient.

Energy Efficiency
ThermoCube is very energy-efficient.  Its thermoelectric modules are powered by a variable voltage power supply that provides the minimum power required to control the temperature at set point, so ThermoCube only draws as much power as needed.  It was also designed to operate in the modules’ most energy-efficient range.

Photos

A ThermoCube 300 is shown with a regulation-size soccer ball for comparison.
The ThermoCubes are the same size.

ThermoCube Front User Interface Panel

Performance

Specifications

Operating Range:	-10 to 50 °C standard range (down to -5 °C with low temp option) (up to 65 °C with high temp option)	Process Fittings:	1/4" John Guest standard
Cooling Capacity:	300 W at 25 °C (25 °C ambient) See Performance Curves	Optional Fittings:	CPC or Swagelok
Modes:	Fixed setpoint, cycling	Noise:	63 dBA at 3 feet (60 or 49 dBA optional)
Precision:	< + 0.05 °C, even near ambient	Size (L x W x H):	12.75 x 11.0 x 12.75" (32.4 x 28 x 32.4 cm)
Coolant:	Ambient air	Weight:	23 lbs
Power:	85-265 VAC, 50 or 60 Hz	Standards:	CE Mark and ENTELA listed to UL61010A-2-10
Alarms:	TTL (temp and system failure), fluid level	Warranty:	2 years

Configuration

Capacity

Options	Purpose	Standard Operating Temperature Range	Standard Operating Temperature Range
200 W	compact, whisper-quiet recirculating liquid chiller, cooled by ambient room air, for up to 200 W (680 BTU/hr) heat load	5 to +50 °C	41 to 122  °F
300 W	same as above, for up to 300 W (1020 BTU/hr)	5 to +50 °C	41 to 122  °F
400 W	same as above, for up to 400 W (1360 BTU/hr)	5 to +50 °C	41 to 122  °F
400 L	recirculating liquid chiller, cooled by house chilled water heat load up to 400 W (1360 BTU/hr)	5 to +50 °C	41 to 122  °F
600 L
300 A	Temperature control of compressed inert gases, heat load up to 300 W (1020 BTU/hr)	5 to +50 °C	41 to 122  °F
400 AC	Enclosure air conditioner, for up to 400 W (1360 BTU/hr)	5 to +50 °C	41 to 122  °F

Pumps

Option	Purpose	Noise	Pressure	Allowed Process Coolant	MTBF (manufacturer's)	Pump Warranty*
1 lpm diaphragm	high pressure, quiet pulse-flow pump	35 dBA	3 bar, 35 psi	Water, glycol/water, alcohol/water, DI water	13,000 hr MTBF	1yr
2 lpm diaphragm	for up to 2 lpm flow rates	40 dBA	40 psi	Water, glycol/water, alcohol/water, DI water	13,000 hr MTBF	1 yr
3 lpm diaphragm	for up to 3 lpm flow rates	45 dBA	45 psi	Water, glycol/water, alcohol/water, DI water	13,000 hr MTBF	1 yr
1 lpm magnetic drive gear	smooth flow, virtually vibration free, stainless steel head allows additional process fluids	63 dBA	3 bar, 40 psi	Water, glycol/water, alcohol/water, DI water, HFE, PAO, Fluorinert, Galden	25,000 hr MTBF	2 yr
2 lpm magnetic drive gear	smooth flow, virtually vibration free, stainless steel head allows additional process fluids	65 dBA	3 bar, 40 psi	Water, glycol/water, alcohol/water, DI water, HFE, PAO, Fluorinert, Galden	25,000 hr MTBF	2 yr
1-2 lpm centrifugal	smooth flow, virtually vibration free, low pressure pump		1 bar (15 psi)	Water, glycol/water, alcohol/water, DI water	25,000 hr MTBF	2 yr

*ThermoCube chiller warranty  is 2 yrs, however diaphragm pumps only carry a 1 yr warranty
Pump Curves can be seen by clicking the Performance tab above

Fans
All fans suitable for indoor, non-condensing environments 

Option	Purpose	Noise at 1 meter
Standard fan	Included in base price	60 to 63 dBA
Quiet fan	Quieter, constant speed operation	57 to 60 dBA
Variable speed fan	Variable speed operation, normal mode at 49 dBA and will increase fan speed as needed to meet setpoint	49 to 60 dBA

Power Cords

Options

United States & Canada

Europe

Japan

United Kingdom

Israel

Australia

Customer specifies power cord for their country. Six standard cords are available at no extra charge. Universal input, 85 - 265 VAC, 50/60 Hz.


Fittings
All options are available on process coolant lines or house water lines.

Option	purpose	tubing size	manufacturer's website
John Guest	simple, push-in fittings for plastic tubing	1/4"	www.johnguest.com
CPC	valved fitting; for easy disconnect and reconnect (not recommended for use with centrifugal pump due to low head pressure)	1/4"	www.colder.com	A mating fitting must match Colder Products part number PLCD16004
CPC metal	toughened version of CPC fitting, chrome-plated brass	1/4"		A mating fitting must match Colder Products part number LCD16004
Swagelok	for use with stainless steel tubing, typically semiconductor applications, very durable	1/4"	www.swagelok.com

Other Options

Communications	RS232 interface controller, enhanced on ThermoCube as of September 2007
Filters	External filter, 5 micron, attaches to chiller externally, adds approx 6" to depth compatible with PAO, water, glycol/water, alcohol/water, DI water
	External air filter mounted onto fan intake grill, adds 1/2" to width of chiller helps eliminate hair, carpet fibers, lint, dust
Fixed Setpoint	Preset control temperature from -5 to +65 No user input buttons on user interface Fixed single setpoint
Extended temperature range	Extends lower range to -5 °C (23 °F)
	Extends upper range to 65 °C (149 °F)
Vibration Reduction	Adds sound dampening material to interior of sheet metal skins Useful for ultra-sensitive SEMS and CCD applications to minimize vibration traveling into fluids
Dry Contact Signals	Dry contact alarm signals
Auto-restart	Software upgrade Upon chiller power-up, unit automatically returns to control at last setpoint temperature (no operator input required)
Optional Fluid Compatibility	Electroless nickel coating on all wetted metal parts
	Options are automatically selected to provide compatiblity with the fluid Choices: PA = PAO SI=Silicon FL=Fluorinert GA=Galden
Custom Engineered Special	Need-specific customization.  Examples include flow switches, custom software, remote temperature probe, custom pumps